We are accepting applications for a full-time Maintenance Engineer III. Visit our career website for more information on specifics. Apply online at www.haysmed.com/careers/ Competitive benefits including health/vision/dental insurance, PTO, and retirementPay Grade Min: $15.6490Position Summary: Under the direct supervision of a Maintenance Manager, the maintenance engineer performs general, rou...
Nylint metalfire engine is 29 inches long. The cab windshield is foggy and the ladder partially works. The paint is intact and it is overall in very good condition. $40/OBO. Cash only. Call or text 785-639-5049
John Deere Model E Hit Miss engine. The box is intact and clean. I have never had the engine out of the box. Text or call 785-639-5049.
This is a type of a Hit Miss engine. I have not had it out of the box and box is in good condition with no tears or stains. $25/OBO. Call or text 785-639-5049
This is a McCormick-Dering Hit-Miss engine in an orginal box. The box shows some damage from opening and closing. I have not had it out of the box, but I did not buy it new. $25/OBO. Call or text 785-639-5049
If you need your mower or small engine fixed, i can help. I work for $20.00 an hour and i can repair most small engine problems. Please call 785-432-1033 to schedule a time.I do NOT work on 2 cycle engines or anything that requires oil to be mixed with gas.
Sears engine performance analyzer with manual and cables. Make offer.
Turbocharged 354 Perkins.Good running takeout.Tested and removed myself.Complete with all wiring, long battery leads, starter, flywheel, bell housing cover and engine mounts.Out of combine. have good Radiator.Reliable and proven engine. 3500.00 diesel swap
Fits M151 MUTT or would be good for a custom built 4 wheel drive vehicle
Oliver Standard "88" panals two front and two backGood condition. dirty, I have not cleaned them$299.00 OBO Jim
High Plains Mental Health Center currently has a full time position opening for an Network Administrator/System Engineer in our Hays Main Office. The Network Administrator/System Engineer uses system analysis techniques and procedures to determine hardware, software or system functional specifications to meet the functional objectives of the Center. This person is responsible for the developmen...
The engine was milled in Hays to about 355ci the transmission is a L60 4E both were rebuild using as highest grade parts I could get .Both have less than 1000 miles It is setting waiting for a new hood to set itself under .It has a quart of Marvel Mistry oil setting in it . I got about $2800.00 but I would offer it for one thousand American cash dollars.It is setting in a pickup front end ready...
I drove the pickup this engine was in home, it had a really low oil pressure and a bad internal noise, but it was not locked up. Swapped in another engine. This engine has been powerwashed, no holes or anything I could find. Comes with a bunch of misc chevy stuff I just want gone, a couple of starters, flexplates, pulleys, hoses, old TBI, coil, distributor, manifolds, water pump, etc. see pics....
Nice Honda engine runs good starts first pull new air filter.
Wanting to sell two small block Chevrolet engines. The first is a 305 2bbl from the late 70s or early 80s. Was running when pulled out of the car, has an attached 350 turbo that. Engine is currently sitting in a frame but easily removed. The other engine is a 1969 350 4bbl out of an Impala. It also has an attached 350 turbo trans. I believe both are probably 2 bolt main engines. Both ran when r...
Engine is complete with carburetor bank, air cleaner, transmission, and ignition switch. Out of a 2000 Honda Magna. 8600 miles on it. 748 cc, liquid cooled.
Selling my aluminum boat and tilt trailer just don't use it like I thought I would It's painted green now not camo no leaks just replaced the bench seats have a 3.5 hp nissan engine and brand new 12volt trolling motor to go with it or will sell without engines $800.00 for boat and trailer or $1250.00 with both engines however you want it Will trade for ??? make an offer !
3.0 ford engine out of a tauras. I have probably 5 or 6 of these
I have lots of engines some fords and chevys and other parts. Some gm 3.1 a few tauras engines older ford and chevy v8. 4.3 chevy. Lots of heads and steering columns. I also have quite a few used transmissions.
I have 2 of these fe series ford engines